Electronic lock "invisible" Supratronik 4940TK bronze Lince

Supratronik electronic lock is invisible from the outside solution with which you can protect your door reliably against theft. The ideal time to further ensure complement your main home, windows, storage, apartment, business, office, van, motor home, house, cellar ... Adaptable to all types of doors: wood, metal, PVC ... It also has a technology integrated alarm, warning of attempted vandalism.

Technical characteristics

lock A-

Dimensions (LxWxH): 155x87x35 (46mm)
Weight: 750 gr. (Excluding batteries)
90 decibel alarm integrated
Batteries: 4 x alkaline AAA batteries (not included)
Battery life: 24 months with an average daily use of 10 starts. The battery life depends on usage.
Operating temperature: -20 - 60
Operating Humidity: 5% - 80%

Remote B-
(Up to 340 possible per unit)

Weight: 30g.
Batteries: 2 button type lithium CR 2016 3V.
Battery life: 60 months with an average daily use of 10 starts.

operating mode

1. White button to link / DELETE COMMANDS
2. External Power 5V (Jack connector 2.35mm)
3. Switch ALARM
4. Antenna
5. Crutch maneuver MANUAL
6. LED
7. alarm speaker
8. CLOSE button remote control
9. OPENING button remote control

Setting remote controls

In the rear of the bolt you have a white key (1) hidden within the body.

1. LINKING CONTROL:
The controls are delivered with unlinked bolt with the bolt. The same control can be linked to more than one lock.

Operating LINKED:
1 1 Press KEY WHITE (1) until the LED (6) to light orange. (No acoustic signal).
1 2 Press any key on the remote control (8) (9) and observe that the LED (6) turns green, the control is linked. (Repeat this point with different controls link).
1 0.3 Once the operation LINK CONTROL wait for the LED (6) goes just completed.
1 .4 Check that the controls are working properly attached from the inside.

* Each bolt link 340 supports commands.
** This operation does not erase previously recorded commands and lets you add new ones.

2. ERASE ALL REMOTE CONTROLS:
2.1 Press and hold the white button (1) until the LED glows RED and hear an acoustic signal.
In case of loss of some control you must perform a clear control and repeat point 1 with existing controls. Lost command will stop working.

Opening and closing the lock with remote control

1. Pressing the close button (8) on the remote control, the red LED will light up for the duration of the maneuver and a beep will be heard when you hang up, which means that the lock is closed.
   * The closing operation of the lock should be done after securing with which the door is properly closed head lock.
2. Pressing the button (9) on the remote control, the GREEN LED will light up for the duration of the maneuver and will hear two beeps when you hang up, which means that the lock is open.
   * The operation of opening the bolt must be done before opening the main door lock.
3. OPERATION FAILED: A closing or opening operation is not performed correctly will result in a failed operation. In this case the bolt beep four times and the LED ORANGE (6) indicating that failed to finish the selected operation will light. In this case the bolt will be prepared for a new attempt.
   ** A botched operation may be due to,
   3.1 friction between the lever and the closer the doorframe, by poor installation or because the door assigned, thus losing the alignment of the bolt.
   3.2 The order to close (8) is activated from the remote control, before the door is completely closed. In this case the lever will collide with closer without going properly in the housing.

Open / close the lock manually

The lock is designed to maneuver manually from inside whenever you want as a manual lock. Ensure that the LED (6) of the bolt is turned off before turning the toggle (5) in closing or opening.

To close the lock: Move the toggle (5) clockwise.

To unbolt: Move the toggle (5) in the anti clockwise.

Alarm (90dB)

This latch is provided with alarm function.

ALARM ACTIVATION ->

1. Activating the ALARM switch (3) moving it to the nearest to the antenna (4) position.
2. Press the CLOSE button (8) on the remote control.
3. You will notice that the red LED flashes 5 times.

OFF ALARM ->

1. Should press the button OPEN (9) on the remote control.
2. It should activate the ALARM switch (3) moving it to the farthest from the antenna (4) position.

Any manipulation of the lock without receiving opening command via the remote control (9) will cause the alarm starts ringing.

Right now, you can only stop the alarm with a remote control (8) (9) linked. The alarm will not respond to ALARM switch (3).

Security mode

If the battery is low bolt, the bolt is designed to enter into a security mode. In this mode if the user attempts to close the lock manually, it opens immediately with the engine.

Thus, it ensures that if the battery is low, is not allowed to be closed manually from inside the house to avoid the risk that, if a child or a dependent one person in the house, they can shut and then you can not open with the command from outside (being exhausted battery).

The lock ensures that the last maneuver before the batteries die is the opening the bolt. This feature prevents the door locks with dead batteries.

Power supply and battery

The lock can be powered by:

• 4 Alkaline AAA batteries
• External auxiliary supply, through the connector OC (2)
  5Vdc 500mA (min) (OC Power connector, Jack, 4 A, 2.35 mm)
  Food s / paragraph 2.5 of the EN60950-1.

** The external power is 5 to 6 Vdc. More than 6V might damage the circuit.

If the batteries are installed and powered externally, the latch use external power and when dropped from the mains, the bolt used batteries.

I recommend leaving the network connected to the auxiliary feeder 5Vdc 500mA (power supply not included) plus 4 new AAA alkaline batteries if you plan to leave the property for a long time.

Box contents

The bolt Supratronik 4940TK of Bricolemar includes the following elements:

components:

Installation

Tools required:

1. Star screwdriver
2. Chisel. (This tool will be needed in the event of having to make changes to the door.)
3. Hammer
4. Drill
5. Broca 02

Prior to installation

Installation Examples

Example installation over a bolt.

example assembly
sliding door.

Recommended position for safety and possible future interventions installation.

example assembly
swing-door

Closer installation under

installation bolt on the door

IMPORTANT: When the installation manually check (make sure you have removed the centralizer CLOSER)

• open door lock / unlock latch.
• door closed, locking / unlocking bolt.

The bolt should not touch at any point closer to the frame.