E "invisible" lock-TK white Supratronik 4940 Lince

Supratronik electronic lock is invisible from the outside solution with which you can protect your door reliably against theft. The ideal time to further secure your main home, windows, storage, apartment, business, office, van, motor home, house, cellar ... Adaptable to all types of doors complement: wood, metal, PVC ... It also has a technology integrated alarm, warning of attempted vandalism.

Technical characteristics

lock A-

Dimensions (LxWxH): 155x87x35 (46mm)
Weight: 750 gr. (Excluding batteries)
90 decibel alarm integrated
Batteries: 4 x AAA alkaline batteries (not included)
Battery life: 24 months with an average daily use of 10 starts. The battery life depends on usage.
Operating temperature: -20 - 60
Operating Humidity: 5% - 80%

Remote B-
(Up to 340 possible per unit)

Weight: 30g.
Batteries: 2 button type lithium CR 2016 3V.
Battery life: 60 months with an average daily use of 10 starts.

Mode operation of the supratronik 4740TK

one. White button to link / DELETE COMMANDS
2. External Power 5V (Jack connector 2.35mm)
3. Switch ALARM
4. Antenna
5. Crutch maneuver MANUAL
6. LED
7. alarm speaker
8. CLOSE button remote control
9. OPENING button remote control

Setting remote controls

At the rear of the bolt you have a white key (1) hidden within the body.

1. LINKING CONTROL:
The controls are delivered with unlinked bolt with the bolt. The same control can be linked to more than one lock.

Operating LINKED:
1 1 Press KEY WHITE (1) until the LED (6) lights in orange. (No acoustic signal).
1 2 Press any key of the remote control (8) (9) and observe that the LED (6) turns green, the control is linked. (Repeat this point with different controls link).
1 0.3 Once the operation LINK CONTROL wait for the LED (6) goes just finished.
1 .4 Check that the controls are working properly attached from the inside.

* Each bolt link 340 supports commands.
** This operation does not erase previously recorded commands and lets you add new ones.

2. ERASE ALL REMOTE CONTROLS:
2.1 Press and hold KEY WHITE (1) until the LED glows RED and hear an acoustic signal.
In case of loss of some control you must perform a clear control and repeat point 1 with existing controls. Lost command will stop working.

Opening and closing the bolt Supratronik with remote control

1. A pressing the lock button (8) on the remote control, the RED LED will light up for the duration of the maneuver and hear a beep to the completion, which means that the lock is closed.
   * Closing operation of the lock should be done after securing the main lock the door is properly closed.
2. A pressing the button (9) on the remote control, the LED will light GREEN duration of the maneuver and will hear two beeps at the completion, which means that the lock is open.
   * OPEN operation of the lock should be done before opening the main door lock.
3. OPERATION FAILED: A closing or opening operation is not performed correctly will result in a failed operation. In this case the bolt beep four times and the LED will light orange (6) indicating that failed to finish the selected operation. In this case the bolt will be prepared for a new attempt.
   ** OPERATION FAILED may be due to,
   3.1 friction between the lever and the closer the doorframe, by poor installation or because the door assigned, thus losing the alignment of the bolt.
   3.2 Triggered order CLOSE (8) from the remote control, before the door is completely closed. In this case the lever will collide with closer without going properly in the housing.

Open / close manually Supratronik latch Lince

The lock is designed to maneuver manually from inside whenever you want as a manual lock. Ensure that the LED (6) of the bolt this ap aga do, before turning the toggle (5) in closing or opening.

To close the lock: Move the toggle (5) clockwise.

To unbolt: Move the toggle (5) in the anti clockwise.

Alarm (90dB)

This latch is provided with alarm function.

ALARM ACTIVATION ->

1. Activating the ALARM switch (3) moving it to the nearest position to the antenna (4).
2. Press the CLOSE button (8) of the remote control.
3. Notice that the red LED flashes 5 times.

OFF ALARM ->

1. You should press the button OPEN (9) of the remote control.
2. Should activate the ALARM switch (3) moving to the position farthest from the antenna (4).

Any manipulation of the bolt without receiving opening command via the remote control (9) will cause the alarm starts ringing.

At this time, only you can stop the alarm with a remote control (8) (9) linked. The alarm will not respond to the ALARM switch (3).

Security mode

If the battery is low the bolt, the bolt is designed to enter into a security mode. In this mode if the user attempts to close the lock manually, it will open immediately with the engine.

Thus, it is ensured that if the battery is low, is not allowed to be closed manually from inside the house to avoid the risk that, if a child or one dependent person in the house, can be enclosed and then you can not open with the command from outside (being exhausted battery).

The lock will ensure that the last maneuver before they run out of batteries is unbolt. This feature prevents the door remains locked with dead batteries.

Power supply and battery

The lock can be powered by:

• 4 Alkaline AAA batteries
• External auxiliary supply, through the OC (2) connector
  5Vdc 500mA (min) (OC Power connector, Jack, 4 A, 2.35 mm)
  Power s / EN60950-1 Section 2.5 of the standard.

** The external power is 5 to 6 Vdc. More than 6V it may damage the circuit.

If the batteries are installed and externally powered, bolt and use the external power if the mains drop, the bolt used batteries.

I recommend leaving the network connected to the auxiliary power supply 5Vdc 500mA (power supply not included) plus 4 new AAA alkaline batteries if you plan to leave the property for a long time.

Contents of the box the 4940TK

The bolt Supratronik 4940TK of Bricolemar includes the following elements:

Components of the bolt "supratronik invisible" Lince:

4970TK bolt installation

Required tool:

1. Star screwdriver
2. Chisel. (This tool will be needed in the event of having to make changes to the door.)
3. Hammer
4. Drill
5. Broca 02

Prior to installation

Installation Examples

mounting example
Sliding door.

Recommended installation position for safety and possible future interventions.

mounting example
hinged door

Closer installation under

4940 bolt installation TK Lince at the door

IMPORTANT: At the end of the installation manually check, (Make sure you have removed the centralizer CLOSER)

• Door open, lock / unlock latch.
• Door closed, locking / unlocking bolt.

The bolt should not touch at any point closer to the frame.

Video demo: